Used on the following heaters:
Mica Band • Ceramic Band •
Mi-Plus • Channel Strip •
Finned Strip • Mica Strip
|
Conventional Ceramic Bases |
Ceramic Caps | ||||||||||
|
All three ceramic cap sizes fit the Convential Ceramic Base |
||||||||||
|
|
Ceramic Cap & Base
for .430" diameter Tubular Heaters
(Primarily used on cast-in heater tubular elements)
|
|
||||||
|
Used on the
following heaters:
Mica Band • Ceramic Band • Mi-Plus • Channel Strip •
Finned Strip • Mica Strip
|
Igloo™ Ceramic Bases |
Ceramic Caps | ||||||||||||||||
|
All three ceramic cap sizes fit all three Igloo Base Types |
||||||||||||||||
|
|
 |
Used
for wiring in high temperature Voltage: 600 VAC Current: 20 Amp Dimensions: 1.56" x 1.24" x .79" Part Number: EHD-108-101 |
Used to insulate bare lead wire at extremely high temperatures
 |
Beads in shipping sleeve |
|
O.D (in) |
I.D (in) |
Length | Packaging | Part Number |
| .110 | .056 | .110 | 67 beads/6" sleeve | CER-103-101 |
| .170 | .068 | .170 | 86 beads/12" sleeve | CER-103-102 |
| .200 | .092 | .200 | 36 beads/6" sleeve | CER-103-103 |
| .200 | .092 | .200 | bulk--loose | CER-103-104 |
| .330 | .124 | .330 | bulk--loose | CER-103-105 |
Used
on channel and finned strip heater mounting tabs to isolate the heater from the mounting surface
A non-standard 1/2" by 5/8" slot in the strip heater is required.
All hardware provided including: screw 2 ceramic bushings 2 washers and nut.
Part Number: CERR-1001
Alloy bus bar is perforated to fit screw terminals of most heaters |
Current Capacity: 35 amps at 300°F (149°C) |
 |
Lugs are used for high temperature service up to 1200°F (649°C) Wire size: 14-16 ga. Order by the piece: 25 pc. minimum
|
Screw Size |
Part Number |
| #12 | TER-111-101 | ||
| #10 | TER-110-104 | ||
| #8 | TER-109-101 |
Terminal boxes used on the following heaters:
Mica Band * Ceramic
Band * Mi-Plus® * Channel
Strip * Finned Strip * Mica
Strip
Can be field retrofit or factory installed
|
|
|
|
|
Mount box on mica ceramic or
MI-Plus band heaters or mica strip heaters.
For use on Standard T3 Terminal mounting centers: 7/8" Size: 2" square by 1-1/2" tallStandard knockout: 5/8" diameter Part Number: HSGR-1011 |
Mount box on mica
ceramic or MI-Plus band heaters or mica strip heaters.
For use on Standard T2 Terminal mounting centers: 7/8" Size: 1-1/2 wide by 2-1/2 long by 1-1/2" tallStandard knockout: 5/8" diameter Part Number: HSGR-1013 |
Enclosure box with
EHDR-1001 cup assembly and jumpers to attach connector to
screw terminals. Use with plug type 900. Mount box on mica
ceramic or MI-Plus band heaters or mica strip heaters.
For use on Standard T3 Size: 2 wide by 2-3/4 long by 1-1/2" tall Terminal mounting centers: 7/8" Part Number: EHDR-1002 |
| Quick Disconnect High Temperature Plugs provide the simplest and safest way to apply power to heater installations. The combination of plug and cup assembly along with armor cable covered leads eliminate all live exposed terminals or wiring that can be a potential hazard to employees or machine | * Durable Cast Aluminum Body
* High Temperature Ceramic Insulators * Solid Brass Contacts * 16 Amp--250 Volt Electrical Rating * Temperature Exposure Up to 300°C (572°F) * Available on Many Tempco Heater Products |
Type HW-900 -- Right-angle plug design Part Number: EHD-101-103 |
Type H-900 -- Straight plug design Part Number: EHD-101-102 |
H900 and HW900 plugs can be prewired and fitted with armor cable or wire braid leads Part Number will be assigned when ordering |
Type UT-900 -- Cup Assembly Part Number: EHDR-1001 |